SirDa shot blasting equipment in a factory

KNOW THE PROCESS. CHOOSE WITH CONFIDENCE.

Practical ideas for surface preparation and machine selection.

Process

What shot peening does to fatigue life

Shot peening is a cold working process: overlapping impacts from spherical shot leave a layer of residual compressive stress at the surface, and that layer is what delays fatigue crack initiation. This article covers the Almen intensity and coverage numbers that define a peening process, why more peening is not always better, which media failures and contamination problems derail a production cell, and how the media separation train, dust collection and exposure time translate into the takt time a continuous line actually runs.

Read article ↗

Process

Removing weld spatter without stopping production

Weld spatter is a functional defect, not just a cosmetic one: it blocks NDE, ruins coating adhesion and disrupts the next weld. Here is what manual removal really costs, how to size an in-line blast station against your takt, and the failure modes that stop the line again.

Read article ↗

Process

Reading a surface profile spec: Ra, Sa and what they miss

A blast cleaning spec usually carries two numbers, and the common mistake is treating them as one. Sa grades describe how clean the steel is, while Ra, Rz and Rmax describe how rough it is. Here is what each parameter actually measures, which instrument belongs with it, and how nozzle pressure, abrasive choice and standoff distance decide the profile you end up with.

Read article ↗

Process

Wet blast versus dry blast: where each one wins

Water does not simply make abrasive blasting gentler. It changes what the machine can do, how the surface comes out, and how much of the surrounding process has to be redesigned. This guide sets out where wet blasting earns its place and where dry still wins, with the corrosion thresholds, the water quality limits and the timing rules that decide the outcome.

Read article ↗

Selection guide

Why hook conveyor speed decides your finish quality

Hook conveyor speed is a process variable, not a handling one. It sets dwell time, and dwell time sets how many abrasive impacts a surface receives. This article works through the arithmetic, the chain speed bands that hold up in practice, and the four failure modes that trace straight back to the speed setting.

Read article ↗

Selection guide

Five questions to ask before quoting a blast room

A blast room quotation is not really a machine quotation. Before you ask for a price, five questions decide whether two suppliers are pricing the same room: what the capacity figure is based on, what the walls and floor are made of, whether the dust collection is sized for the duty, which wear parts you will keep buying, and who responds when it stops.

Read article ↗

Selection guide

Tumble belt versus mesh belt: which conveyor fits the part

Tumble belt and mesh belt machines both carry parts through an abrasive stream, but they buy their result in opposite currencies. Tumbling exposes every surface by moving the part and pays for it in collision damage; a supported mesh belt protects a cosmetic finish by holding the part in place and pays for it in shadowing and belt wear. This guide works from part geometry - impact tolerance, blind bores and parting lines, wall thickness, size envelope, mix stability - through the arithmetic of a fixed drum batch versus continuous belt exposure, and into the failure modes each machine brings: run-off, broken wires and embedded scale on the mesh side, liner wear and door seal leaks on the drum side.

Read article ↗

Automation

PLC, HMI and remote monitoring in modern blast rooms

A modern blast room is a control problem as much as a blasting problem. This guide walks through what the PLC actually sequences, the interlocks worth demanding in writing, how process data should be captured for peening and coating work, and the predictable ways automated blast rooms fail in day-to-day production.

Read article ↗

Buying guide

What CE marking actually covers for a blast machine

The CE mark on a blast machine is a manufacturer's own declaration, not a third-party certificate. Here is what it legally covers, the four documents that must agree with each other, and the blast-specific hazards where conformity most often breaks down.

Read article ↗

Applications

Surface prep for hot-dip galvanizing: what the fab shop needs

Zinc does not bond to dirty steel, which makes hot-dip galvanizing self-checking. Where abrasive blasting fits in the degrease-pickle-flux chain, why preparation before galvanizing and touch-up after it demand opposite media, and how to size nozzles, airflow and dust collection honestly.

Read article ↗

Your next project

Let’s find your solution.

Send your workpiece and production requirements.
Let’s define the right blasting system.

Request a quotation