Skip to content
Journal /Troubleshooting

Shot Blasting Defect Diagnosis Chart: Symptom to Cause

A reference chart mapping nine visible blast-cleaning defects to their likely cause, first check and correction — from shadowing and rust bloom to over-peening and media loss.

Shot Blasting Defect Diagnosis Chart: Symptom to Cause

How to use this chart

Blast cleaning faults are rarely random. A surface that fails inspection is the end of a chain: abrasive condition, wheel setup, machine handling, extraction and the specification itself. This chart starts from what you can see on the part and works backwards to the control that actually moves the result.

Read the symptom column first. Each row gives the mechanism, the checks in the order that eliminates possibilities fastest, and the correction. Where two causes produce the same appearance, the discriminating check is named.

Symptom-to-cause chart

SYMPTOM                  MOST LIKELY CAUSE           FIRST CHECK                    FIX
------------------------------------------------------------------------------------------------
Patchy cleaning,          Shielding: parts too       Look at how parts sit in     Space the load; add
repeatable shadow areas   close or nested on the     the drum / on the hook       turnover or a second
in the same place         carrier                                                 orientation
------------------------  --------------------------  -----------------------------  -------------------
Uneven cleanliness across Wheel streams not covering Check wheel angles against   Re-aim wheels; add a
the width of a plate      the full working width     the actual part section      station
------------------------  --------------------------  -----------------------------  -------------------
Rust blooms back within   No anchor profile despite  Measure Rz to ISO 8503        Correct abrasive size
days after blasting       adequate Sa cleanliness    on a test panel              and working mix
------------------------  --------------------------  -----------------------------  -------------------
Surface too smooth,       Abrasive too fine or too   Compare delivered grit to     Reclassify media;
coating lacks tooth       heavily degraded           SAE J444 / ISO 11124 size     restore working mix
------------------------  --------------------------  -----------------------------  -------------------
Deep Regular polishing    Oversized shot or excessive Check Almen intensity on     Reduce wheel power
pattern (over-peening)    wheel energy               the strip                     or shot size
------------------------  --------------------------  -----------------------------  -------------------
Dust film on parts after  Extraction too low or      Check airflow at the chamber Correct fan / filter
the cycle                 filter overloaded          opening                       settings
------------------------  --------------------------  -----------------------------  -------------------
Abrasive carry-out into   Open cavities not drained;  Inspect discharge and mask   Add drainage, angled
the downstream line       separator overloaded       setup                         pass or masking
------------------------  --------------------------  -----------------------------  -------------------
High media loss per hour  Leakage at seals, elevator  Weigh circulation vs make-up Seal leaks; clean
                          or separator overload      rate                          separator
------------------------  --------------------------  -----------------------------  -------------------
Impact marks on machined  Parts contacting each other Measure batch mix on a       Separate parts or
faces                     or a wrong belt type       sample load                   switch carrier
------------------------  --------------------------  -----------------------------  -------------------
Belt or drum wear spikes  Tramp metal or oversized    Screen the abrasive supply   Restore screening
                          hard particles in the mix                                and grading

The five checks that resolve most cases

Work through these before changing machine settings. In field practice the cause is usually upstream of the wheel.

  1. Confirm the specification. Write down the Sa grade (ISO 8501-1), the Rz range (ISO 8503) and the coating data sheet requirement. Many "cleaning failures" are a mismatch between what the shop believes was specified and what the standard actually says.
  2. Sample the abrasive actually in circulation, not the bag. Size distribution drifts as media degrades; a working mix that has lost its coarse fraction will not produce the profile the specification calls for. Test to ISO 11125.
  3. Verify exposure time and line speed. A wheel running at the correct power for too short a dwell gives the same result as an underpowered wheel. Time a single part through the blast zone.
  4. Inspect part presentation. Shadowed areas, nesting and flat parts lying on a belt account for more rejected batches than wheel faults. Check the load, not the machine.
  5. Measure before adjusting. Use a cleanliness comparator for Sa and a profile gauge or replica tape for Rz. Visual judgement alone cannot distinguish "clean enough" from "clean with the wrong profile".

When the fault is in the specification, not the machine

Three requirements are physically impossible or unstable and should be challenged before a machine is bought or a batch is rejected:

  • A single Sa grade applied to every part in a mixed batch. Different geometries and surface conditions reach different grades under the same cycle.
  • An Rz range narrower than the abrasive can deliver. A coarse grit produces a broad profile band; tightening the range means changing the media, not the machine.
  • "Clean to Sa 2.5" with no profile requirement. Coating adhesion depends on the anchor pattern. Cleanliness alone does not protect against adhesion failure.

Recording a fault so it can be diagnosed remotely

A useful fault report contains six facts: the part, the abrasive grade and its test date, the wheel power and amperage, the cycle or line speed, the measured Sa and Rz values, and a photograph in fixed lighting. Without those, a supplier can only guess — and the usual guess is "more power", which fixes very few real faults.

Where to go next

  • For the process behind the grades, see the guide to ISO 8501 Sa 2.5 and anchor profile engineering.
  • For choosing the right media before a fault appears, see the abrasive selection and working-mix guides.
  • For matching a machine to a workpiece, start with the machine selection guide.

Related machines

Related machines

Related articles

Your next project

Let’s find your solution.

Send your workpiece and production requirements.
Let’s define the right blasting system.

Request a quotation